Custom Propeller Bore Machining – Shaft Bore, Taper and Keyway
Custom Propeller Bore Machining – Shaft Bore, Taper and Keyway
Custom machining service for adapting a VETUS propeller hub to the dimensions of an existing propeller shaft.
- Supplied as an additional service with a compatible propeller
- Customer receives a measurement drawing after purchase
- Required shaft, taper and keyway dimensions must be provided
- Bore, taper and keyway are machined to the confirmed measurements
- Machining is only possible when sufficient hub material remains
- The finished propeller is customised and cannot normally be returned
The Custom Propeller Bore Machining service is used when the standard bore of a VETUS propeller does not match the existing propeller shaft.
After purchase, VetusOnline will send a technical drawing showing the measurements required. The customer must measure the propeller shaft carefully and return the completed drawing before machining can begin.
The service may include adaptation of:
- Propeller shaft bore
- Taper dimensions
- Taper ratio
- Keyway width and depth
- Hub length, where relevant
Measurements required
The exact measurements depend on the shaft installation. The drawing supplied by VetusOnline will indicate which dimensions must be provided.
These may include:
- Largest taper diameter
- Smallest taper diameter
- Taper length
- Taper ratio
- Shaft diameter
- Keyway width
- Keyway depth
- Thread and retaining nut details
All dimensions must be measured accurately. The quality and fit of the finished machining depend on the information supplied by the customer.
Machining approval
The standard propeller hub can only be enlarged or modified when sufficient material remains around the bore to preserve the required strength.
VetusOnline will review the requested dimensions before confirming that the machining is possible. Some shaft sizes, taper dimensions or keyways may not be suitable for the selected propeller hub.
Machining will not begin until:
- The completed measurement drawing has been received
- The dimensions have been reviewed
- Any unclear measurements have been confirmed
- The selected propeller has been approved for the requested modification
Important information
This service must be purchased together with the propeller that requires machining.
The customer is responsible for providing correct and complete shaft dimensions. Measurements should preferably be taken from the shaft itself rather than from the old propeller, as an existing propeller may be worn or previously modified.
Once machining has started, the propeller becomes a customised product. Custom-machined propellers cannot normally be cancelled, exchanged or returned.
Additional processing time is required before the propeller can be shipped.
Leverans
När varan kan skickas beror på dess tillgänglighet. Leveranstiden påverkas också av din leveransadress och det fraktsätt du väljer. I vår fraktinformation kan du läsa om leveransalternativ, beräknade tider för avsändning och transport samt fraktkostnader.
Behöver du en vara till ett visst datum? Kontakta oss innan du beställer.
Returer och reklamationer
Vill du returnera en vara eller reklamera en defekt, skadad eller fellevererad produkt? Börja med att skapa ett ärende i vårt retur- och reklamationssystem online. Vi hjälper dig med nästa steg.
The Custom Propeller Bore Machining service is used when the standard bore of a VETUS propeller does not match the existing propeller shaft.
After purchase, VetusOnline will send a technical drawing showing the measurements required. The customer must measure the propeller shaft carefully and return the completed drawing before machining can begin.
The service may include adaptation of:
- Propeller shaft bore
- Taper dimensions
- Taper ratio
- Keyway width and depth
- Hub length, where relevant
Measurements required
The exact measurements depend on the shaft installation. The drawing supplied by VetusOnline will indicate which dimensions must be provided.
These may include:
- Largest taper diameter
- Smallest taper diameter
- Taper length
- Taper ratio
- Shaft diameter
- Keyway width
- Keyway depth
- Thread and retaining nut details
All dimensions must be measured accurately. The quality and fit of the finished machining depend on the information supplied by the customer.
Machining approval
The standard propeller hub can only be enlarged or modified when sufficient material remains around the bore to preserve the required strength.
VetusOnline will review the requested dimensions before confirming that the machining is possible. Some shaft sizes, taper dimensions or keyways may not be suitable for the selected propeller hub.
Machining will not begin until:
- The completed measurement drawing has been received
- The dimensions have been reviewed
- Any unclear measurements have been confirmed
- The selected propeller has been approved for the requested modification
Important information
This service must be purchased together with the propeller that requires machining.
The customer is responsible for providing correct and complete shaft dimensions. Measurements should preferably be taken from the shaft itself rather than from the old propeller, as an existing propeller may be worn or previously modified.
Once machining has started, the propeller becomes a customised product. Custom-machined propellers cannot normally be cancelled, exchanged or returned.
Additional processing time is required before the propeller can be shipped.
Leverans
När varan kan skickas beror på dess tillgänglighet. Leveranstiden påverkas också av din leveransadress och det fraktsätt du väljer. I vår fraktinformation kan du läsa om leveransalternativ, beräknade tider för avsändning och transport samt fraktkostnader.
Behöver du en vara till ett visst datum? Kontakta oss innan du beställer.
Returer och reklamationer
Vill du returnera en vara eller reklamera en defekt, skadad eller fellevererad produkt? Börja med att skapa ett ärende i vårt retur- och reklamationssystem online. Vi hjälper dig med nästa steg.
Tack för din tid och dina synpunkter.
Ditt bidrag hjälper oss att göra informationen på VetusOnline tydligare och mer korrekt och webbutiken enklare att använda.
Referensnummer: